DS1985
PROGRAM PULSE TIMING DIAGRAM Figure 11
LINE TYPE LEGEND:
Bus master active high
(12V @ 10 mA)
Resistor pullup
CRC GENERATION
With the DS1985 there are two different types of CRCs (Cyclic Redundancy Checks). One CRC is an 8-
bit type and is stored in the most significant byte of the 64-bit ROM. The bus master can compute a CRC
value from the first 56 bits of the 64-bit ROM and compare it to the value stored within the DS1985 to
determine if the ROM data has been received error-free by the bus master. The equivalent polynomial
function of this CRC is: X 8 + X 5 + X 4 + 1. This 8-bit CRC is received in the true (non-inverted) form
when reading the ROM of the DS1985. It is computed once at the factory and lasered into the ROM.
The other CRC is a 16-bit type, generated according to the standardized CRC16-polynomial function X 16
+ X 15 + X 2 + 1. This CRC is used to safeguard user-defined EPROM data when reading data memory or
status memory. It is the same type of CRC as is used with NV RAM based iButtons to safeguard data
packets of the iButton File Structure. In contrast to the 8-bit CRC, the 16-bit CRC is always returned in
the complemented (inverted) form. A CRC-generator inside the DS1985 chip (Figure 12) will calculate a
new 16-bit CRC at every situation shown in the command flow chart of Figure 5.
The DS1985 provides this CRC-value to the bus master to validate the transfer of command, address, and
data to and from the bus master. When reading the data memory of the DS1985 with the Read Memory
command, the 16-bit CRC is only transmitted as the end of the memory is reached. This CRC is
generated by clearing the CRC generator, shifting in the command, low address, high address and every
data byte starting at the first addressed memory location and continuing until the end of the implemented
data memory is reached.
When reading the status memory with the Read Status command, the 16-bit CRC is transmitted when the
end of each 8-byte page of the status memory is reached. At the initial pass through the Read Status flow
chart the 16-bit CRC will be generated by clearing the CRC generator, shifting in the command byte, low
address, high address and the data bytes beginning at the first addressed memory location and continuing
until the last byte of the addressed EPROM Status data page is reached. Subsequent passes through the
Read Status flow chart will generate a 16-bit CRC that is the result of clearing the CRC generator and
then shifting in the new data bytes starting at the first byte of the next page of the EPROM Status data
field and continuing until the last byte of the page is reached.
22 of 26
相关PDF资料
DS1990A-F3+ IC IBUTTON SERIAL NUMBER F3
DS1990R-F5# IBUTTON SERIAL NUMBER F5
DS1993L-F5+ IBUTTON MEMORY 4KBit F5
DS1995L-F5+ IBUTTON MEMORY 16KBit F5
DS1996L-F5+ IBUTTON MEMORY 64KBit F5
DS9092K# KIT IBUTTON STARTER
DS9502P+T&R DIODE ESD PROTECTION 6-TSOC
DS9503P+ DIODE ESD PROTECTION W/RES 6TSOC
相关代理商/技术参数
DS1985-F5 功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1985-F5# 功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1985-F5+ 功能描述:iButton 16Kb Add-Only iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1985U 制造商:未知厂家 制造商全称:未知厂家 功能描述:UniqueWare iButton
DS1985U-F5-117D+ 功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1986 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:64-kbits Add-Only iButton⑩
DS1986+F3 制造商:Maxim Integrated Products 功能描述:ADD-O IBTN 64KB, F3 (GENERIC) LFREE - Rail/Tube
DS19860-F3-W 功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated